Intel Pentium D 920, 930, and 940 Processors (Dual-Core,
2.8 GHz, 3.0 GHz and 3.2 GHz, 2 x 2MB Level 2 cache, and 800MHz front-side-bus).
At A Glance
The HP ProLiant ML110 G3 is a remarkable
value for workgroups or small-to-medium businesses. It provides dependable
server performance with appropriate technology and features an affordable
price.
Processors:
Intel Dual-Core Pentium D processors and Single-core
Pentium 4 and Celeron D processors
Intel E7230 Chipset with 800MHz FSB (Pentium
4) or 533MHz FSB (Celeron D)
Memory:
512 MB of ECC PC2 4200 DDR II SDRAM memory standard
(8GB maximum)
Storage Controller:
Integrated Single Channel Ultra ATA for optical
drive
Internal Drive Support:
Up to three Ultra320 non-hot plug SCSI hard
disk drives or non-hot plug SATA hard disk drives.
Three drive deployments require the use of a
conversion kit on all models and the 6-port SATA RAID Controller
on the SATA Models
Internal storage capacity of up to 438GB (3
x 146GB non-hot plug SCSI HDD) (SCSI Models)
Internal storage capacity of up to 1.5TB (3
x 500GB non-hot plug) SATA HDD (FIO SATA Model)
Network Controller:
Broadcom 5721 Gigabit NIC (embedded) 10/100/1000
WOL (Wake on LAN)
Embedded Serial ATA (SATA Models) or a Single
Channel Ultra320 SCSI Adapter (SCSI Models)
Expansion Slots:
Four total I/O slots: two 32-bit/33MHz PCI (3.3
Volt) slots and two PCI-Express slot (x4 and x8(x16connector)).
USB Ports:
Six (USB 2.0 ports (2 rear, 2 front, 2 internal)
Two serial ports
Optical Drives:
CD-ROM ships standard
Power Supply:
350W Power Supply
Form Factor:
4U chassis
Management:
Lights-Out 100 Remote Management card (optional)
ROM Based Setup Utility (RBSU) and PXE support
Integrated ATI ES1000 16 MB video
Warranty:
Protected by HP Services and a worldwide network
of resellers and service providers. One-year Next Business Day,
on-site limited global warranty (one year parts, one year labor,
and one year on-site (1-1-1)). Certain restrictions and exclusions
apply. Pre-Failure Notification on processors, memory, and SCSI
hard drives. (Note: AP offers a 3-1-1 warranty on the ML110 G3)
Cache Memory One of the following depending on Model
256KB Level 2 ECC cache (Celeron
D models)
2048KB Level 2 ECC cache (Pentium
4 models)
2x2048KB Level 2 ECC cache (Pentium
D models)
Chipset
Intel E7230 Chipset with 800Mhz
FSB (Pentium 4 and Pentium D)
Intel E7230 Chipset with 533Mhz FSB
(Celeron D)
Memory Protection
Un-buffered standard ECC capabilities
ML110 G3 Memory One of the following depending on Model
Type
PC2-4200 unbuffered DDR2 SDRAM
(533MHz)
Standard
512
MB (on Pentium
D, Pentium-4 and Celeron D models)
Maximum
8 GB
Network Controller
Broadcom 5721 Gigabit NIC (embedded)
10/100/1000 WOL (Wake on LAN)
Expansion Slots
Slot
Number
Bus Speed
Hot Plug Y/N
PCI Voltage
Notes
1
x8 PCI Express
No
n/a
In a x16 slot
Full Height
1
x4 PCI Express
No
n/a
Full Height
2
32bit/33MHz PCI
No
3.3V
Full Height
Storage Controller
One of the following depending on Model
HP Single Channel Ultra320 SCSI
Adapter (SCSI Models)
Integrated 2 ports Serial ATA
(SATA Models)
Storage
CD-ROM
48x IDE (ATAPI) CD-ROM Drive
Hard Drives
One of the following:
36GB Ultra320 SCSI 15,000 rpm Hard Drive (Standard on SCSI models)
80GB SATA 7200 rpm Hard Drive (Standard on SATA Models)
Maximum Internal
Storage
Type
SCSI (Non-hot plug)
438GB
(3 x 146GB)
SATA (Non-hot plug)
1.5TB
(3 x 500GB)
*NOTE:
Available via FIO only
NOTE:
Maximum internal storage utilizes 2 internal drive bays and 1 removable
media bay.
NOTE:
For SCSI models, configuring the media bay to hold the 3rd hard disk drive
requires the purchase of the bracket conversion option kit (P/N 396654-B21).
NOTE:
For SATA models, both the bracket conversion option kit (P/N 396654-B21)
and the HP 6-Port SATA RAID Controller Option Kit (P/N 372953-B21) are required
for the installation of the 3rd HDD.
Interfaces
Parallel
1
Serial
2
Pointing Device (Mouse, PS2)
1
Graphics
1
Keyboard (PS2)
1
USB
6 (2 rear, 2 front panel, 2 internal)
Dedicated USB 1 internal (available for USB
tape connectivity)
NOTE:
Rack models ship standard with a 12' IEC cable. Most redundant power
supply options ship with a 6' country specific power cord. Localized cables
included with geographic specific models in other world regions.
Power Supply
350 Watts
System Fans
1 - non-redundant system fan
shipped standard
1 - non-redundant CPU heatsink
fan shipped standard
OS Support
Microsoft Windows Server 2003:
Standard (32 and 64 bit)
Microsoft Windows Small Business Server 2003: Standard & Premium Edition
Windows 2000 Server - Standard Edition
Novell NetWare 6.5 SBS
Red Hat Enterprise Linux 4 ES (32 and 64 bit)
HP Factory Express offers configuration,
customization, integration and deployment services for HP servers and/or
storage products. Customers can choose how their factory solutions are built,
tested, integrated, shipped and deployed.
Factory Express offers service packages for simple configuration, racking,
installation, complex configuration and design services as well as individual
factory services, such as image loading, asset tagging and custom packaging
HP products supported through Factory Express include a wide array of
servers and storage: HP Integrity, HP ProLiant, HP ProLiant Server Blades,
HP BladeSystem, HP 9000 servers, as well as, the MSA1000, VA7xxx, EVA,
XP, rackable tape libraries and configurable network switches.
For more information
on Factory Express services for your specific server model please contact
your sales representative or go to http://www.hp.com/go/factory-express.
HP Enterprise Configurator
The HP eCo-Enterprise Configurator
now provides factory default racking for our HP hardware portfolio. This
approach is aligned with our strategic direction to meet the needs and expectations
of our valued customers. If you require "custom" rack configuration,
please contact HP's Customer Business Center or an Authorized Partner for
assistance.
HP ProLiant Smart
Buys
(NA only)
The HP Smart Buy program offers mainstream business solutions at competitive
prices with excellent availability and superior HP quality. It offers
a wide range of industry-leading HP products at compelling prices, allowing
you to receive richer configurations with additional options.
This product is covered by a global limited warranty and supported by
HP Services and a worldwide network of resellers and service providers.
Hardware diagnostic support and repair is available for one year from
date of purchase. Support for software and initial setup is available
for 90 days from date of purchase. Additional support may be covered under
the warranty or available for an additional fee. Enhancements to warranty
services are available through HP Care Pack services or customized service
agreements.
NOTE: Limited warranty includes 1 year
parts, 1 year labor, 1-year on-site support (3-1-1 warranty offered in
AP only). Additional information regarding worldwide limited warranty
and technical support is available at: http://h18004.www1.hp.com/products/servers/platforms/warranty/index.html
HP Care Pack services include coverage for the HP branded hardware options
qualified for the server, purchased at the same time or afterward, internal
to the enclosure, as well as 22" and smaller external monitors and
tower UPS options up to 3kVA; these items will be covered at the same
service level and for the same coverage period as the server. Coverage
of UPS Battery is not included, standard warranty terms & conditions
apply. For servers or storage systems installed within a rack, service
also covers all HP qualified rack options installed within the same rack.
HP services provide continuous care and support expertise with committed
response designed to meet your IT and business needs.
To fully capitalizing on your HP ProLiant servers' capabilities requires
a service partner who thoroughly understands your server technology and
systems environment. HP Services, an industry leader in provision of multi
vender support solutions provides a range of support services designed
to meet the varying needs of business. Whether an SMB or large global
corporation HP has a ProLiant server support offer to help you speedily
deploy and maximize system uptime.
Enhanced Care - Minimum recommended service support offer designed to
ensure customers have access to expert assistance, whenever they need
it.
Next Business Day on site coverage, 3 Years
Continuance Care - Recommended service, delivering cost-effective support
options designed to extend HP Services committed response and guaranteed
fix times, designed to speed problem identification and resolution.
4-Hour On-site Service, 5-Day x 13-Hour Coverage, 3 Years
Total Care - Highest HP Support service level recommend to help increase
IT performance and availability with comprehensive, integrated hardware
and software services
4-Hour On-site Service, 7-Day x 24-Hour Coverage, 3 Years
Deployment Services - HP Installation and Start Up services designed
to take time, risk, and worry out of the deployment of ProLiant servers
- and free customers IT support staff to focus on what they do best, their
business.
Installation of a ProLiant server as per Data Sheet. To be delivered
on a scheduled basis 8am-5pm, M-F, excl. HP holidays
Configuration Information-Factory Integrated Models (North America Only)
NOTE:
For Configure to Order requirements within EMEA region, please consult
local Sales Contact.
NOTE: HP does not allow factory integration of options into standard
models listed above.
Configure-to-order servers must start with a CTO Chassis. NOTE: This product offering does
not support HP Factory Express Server Configuration Level 1. NOTE: FIO indicates that this option
is a Factory Installable Option.
Step 1:
Base Configuration
Models
HP ProLiant ML110 G3 SATA Tower
Chassis (North America)
393256-405
Factory Integrated Models
ship with:
Broadcom 5721 Gigabit NIC (embedded)
10/100/1000 WOL (Wake on LAN)
Keyboard and Mouse
350 Watts, PFC (Power Factor Correcting)
Tower Form Factor (4U)
HP ProLiant ML110 G3 SCSI Tower
Chassis (North America)
393257-405
Factory Integrated Models ship
with:
Broadcom 5721 Gigabit NIC (embedded)
10/100/1000 WOL (Wake on LAN)
SCSI Host controller
Keyboard and Mouse
350 Watts, PFC (Power Factor Correcting)
Tower 4U Form Factor
Step 2: Choose Required
Options (only one of the following from each list unless otherwise noted)
Processors
Single-Core Intel Celeron D Processor
326 2.53 GHz/533MHz Factory Integrated
NOTE:
SCSI Storage Controllers are qualified for SCSI drives only and do not support
the SATA Drives. NOTE: SATA Storage Controllers are
qualified for SATA drives only and do not support the SCSI Drives.
Step 4: Choose Additional Options
for Factory Integration
Operating Systems
Pre-install Microsoft Windows
2003 SBS Standard Edition
W2003 SBS STD PL1XX
379601-XX1
W2003 SBS PRM PL1XX ENG
379603-XX1
NOTE: For additional
options, please refer to the "Options" section below.
NOTE:
For the installation of Windows and other OS's, a floppy drive may be required
to complete driver installation. A USB drive key may not work to complete driver
installation.
NOTE: When purchasing
systems with the 500GB NHP SATA drives, please reference the Configuration
Information Section of this QuickSpecs to order via Configuration to Order.
HP External 160GB
HDD
HP External Backup Solution by
Seagate (North America)
NOTE: SCSI Storage
Controllers are qualified for SCSI drives only and do not support the SATA
Drives. NOTE: SATA Storage Controllers are qualified for SATA drives only
and do not support the SCSI Drives.
HP StorageWorks DAT 72 SCSI Internal
Tape Drive (Carbon)
Q1522B
NOTE:
Installation of SCSI internal tape drives in a ML110 G3 model requires SCSI
controller kit (PN: 374654-B21).
HP
Data Protector Express Software
HP
DP Express Backup Server Upgrade for ProLiant Software
BB117AP
HP DP Express Package for Microsoft
Small Business Server
BB118AA
NOTE: Please see
the HP Data Protector Express QuickSpecs for additional information regarding
the purchase of HP Data Protector Express software: http://h18000.www1.hp.com/products/quickspecs/12337_div/12337_div.html
(Worldwide) NOTE: To obtain a free licensed copy of HP Data Protector Express
for ProLiant edition software, please visit the "Protect Your Data"
link accessible from your ProLiant server's System Management Homepage (SMH)
software (SmartStart 7.5 or later).
Installation of Server
into Racks
100Kg/220Lbs Sliding shelf (Graphite)
NOTE: When using the100Kg/220Lbs Sliding shelf, install Stabilizer
Kit for 5642 rack (PN 374493-B21).
NOTE: Cat5e cables
are required to connect Interface Adapters to Console Switches. Cat5e cables
can be found at the following URL: http://www.hp.com/go/kvm
HP 1x4 USB/PS2 KVM Switch, TT
(NA/JPN)
371301-D71
HP 1x4 USB/PS2 KVM Switch, TT
(AU/NZ)
371301-011
HP 1x4 USB/PS2 KVM Switch, TT
(UK)
371301-031
HP 1x4 USB/PS2 KVM Switch, TT
(EU)
371301-A21
HP 1x4 USB/PS2 KVM Switch, RM
(ALL)
371302-B21
HP PS2 KVM Cable with audio, 6'
2-pack
371730-B21
HP USB KVM Cable with audio, 6'
2-pack
371729-B21
NOTE: For additional
information regarding KVM Switches, Serial Console servers, rack mount monitors,
keyboards and all related options please see the following URL: http://www.hp.com/go/kvm
HP ProLiant ML110 G3 Celeron D and
Pentium 4 Models
Standard Memory
512 MB of PC2-4200 DDR2 SDRAM
running at 512 MB with Advanced ECC capabilities Memory installed (1 x 512
MB SDRAM DIMM).
Standard Memory Plus Optional
Memory
Up to 5120 MB memory is available
with the optional installation of PC2-4200 Registered un-buffered ECC DDR2
SDRAM DIMM Memory kits.
Standard Memory Replaced
with Optional Memory
Up to 8192 MB of memory is available
with the removal of the standard 512 MB of memory and the optional installation
of PC2-4200 Registered un-buffered ECC DDR2 SDRAM DIMM Memory kits.
NOTE: The below
chart does not represent all possible memory configurations. NOTE: In memory configurations requiring 2 DIMM and 4 DIMM configurations,
the memory must be paired for optimal performance. This means that DIMMs
in slot 1 and 3 have to be identical, in slot 2 and 4 have to be identical.
(For example, the Optional memory configuration shown below)
ML110 G3 Memory
Slot
4
3
2
1
Standard
512 MB
Empty
Empty
Empty
512 MB
Optional
5120 MB
2048 MB
512 MB
2048 MB
512 MB
Maximum
8192 MB
2048 MB
2048 MB
2048 MB
2048 MB
Following are memory options available from
HP:
512 MB Unbuffered Advanced ECC PC2-4200 DDR2 (1 x 512 MB), Single
Rank
Hot Plug Single Channel Ultra320
SCSI Adapter (SCSI Models)
NOTE: Support
for position "B" requires the purchase of bracket conversion kit
(P/N 396654-B21).
ML110 G3 Hard Drives (SATA Models only)
SATA
1.5Gb - Non-Hot Plug
Quantity Supported
Position Supported
Controller
3.5-inch 80GB 160GB 250GB 500GB
Up
to 3
1, 2 or B
HP 6-Port SATA RAID Controller
NOTE: Support
for position "B" requires the purchase of bracket conversion kit (P/N 396654-B21).
NOTE: 1st and
2nd hard disk drive requires no additional controller. Addition of the 3rd hard
disk drive requires the purchase of HP 6-Port SATA RAID Controller (P/N 396654-B21).
Maximum Storage
Capacity -SCSI Models
Internal
438GB (3 x 146GB non-hot-plug
hard drives)
Total
438GB
Maximum Storage
Capacity - Non-Hot Plug SATA Models
Internal
750GB (3 x 250GB
non-hot-plug hard drives)
Total
750GB (3 x 250GB
non-hot-plug hard drives)
1.5TB (3 x 500GB via FIO or specials only)
NOTE:
Maximum internal storage utilizes 2 internal drive bays and 1 removable
media bays. NOTE: The addition of the 3rd hard disk drive for SCSI maximum internal
storage support requires the purchase of the bracket conversion option kit
(P/N 396654-B21). NOTE: The addition of the 3rd hard disk drive for SATA maximum internal
storage support requires the purchase of the bracket conversion option kit
(P/N 396654-B21) and SATA RAID Controller (P/N 372953-B21.)
Tape
Drives
NOTE:
A SCSI controller needs to be purchased to operate internal SCSI devices in the
SATA Models. NOTE: For an up-to-date listing of the latest O/S Support
details for each of the Tape Drives listed below, please see the following: http://h18000.www1.hp.com/products/quickspecs/Division/10233.html
(Worldwide)
Quantity Supported
Position Supported
Controller
Internal
USB Tape Drives HP DAT 24 USB HP DAT 40 USB HP DAT 72 USB
1
B
Internal
USB 2.0 port
Internal
SCSI Tape Drives HP DAT 40 SCSI HP DAT 72 SCSI
System Leakage with all power supplies loaded
(mA)
0.75mA@240V
0.45mA@120V
System Inrush Current with all power supplies
loaded (A)
80A
Power cord requirements
Nema 5-15P to IEC320-C13
IEC320-C13 to IEC320-C14
**Power shown is for
a fully configured system consisting of (1) CPU, (4) double-sided DIMMs,
(4) HDDs, (1) CD-ROM, (1) DVD-ROM, (4) PCI cards, and (1) power supply.